Fallo Modulo ABS Sensor G85

[Robledo]

Hola a todos. Despues de haber desconectado la batería para poder cambiar unas bombillas a los faros y no quedarme achicharrado ya que son de xenon, le he pasado el Vag-Com y aparecian varios fallos. He borrado todos pero hay uno que no se me borra.

Sensor G85 de angulo de giro.

Por mas veces que lo borro aparece al momento. Pero me extraña ya que ha salido a raiz de desconectar la bateria.

Hay que hacer algun tipo de ajuste básico o algo parecido? Si es asi como se hace?

Es que mañana viajo y mejor no ir pelao sin ABS, ni ESP ni nada.

O puede ser que haya saltado algun fusible al reconectar la bateria?

[javiersan]

Cuando andes unos metros en linea recta se borra solo.
Ya nos cuentas.

[Robledo]

Ya lo habia probado pero se ve que no era suficiente. He cojido esta informacion de Ross-Tech


ESP Steering Angle Sensor Calibration
Updated 5 Aug. 2011




Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual ([Only registered and activated users can see links]) for your vehicle!

This procedure details how to perform the zero position calibration for the Steering Angle Sensor (G85) in many VW/Audi vehicles equipped with ESP (Electronic Stability Program). This procedure should be performed when vehicle alignment is performed or if any of the following components have been removed or replaced:

ABS/EDL/ASR/ESP control unit (J104)
Steering Angle Sensor (G85)
Steering Column
There are certain test conditions that must be met before doing this procedure:

Start the vehicle.
Turn the steering wheel one turn to the right and one turn to the left.
Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight
Ensure that the steering wheel is not moved again.
Keep the engine running and do not switch off the ignition.
Procedure for performing the zero position calibration for the Steering Angle Sensor (G85) on VW Golf, GTI, Jetta, and Audi TT:
[Select]
[03 - ABS Brakes]
[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 060 (do NOT scroll up and down in the Basic Settings function, type in 060 instead)
[Go!]
This will store the zero (centered) position of the steering wheel. There should be a displayed message that reads: "Steer. angle sender compens OK". If you get an error, it may mean the Login was not successfully performed.
Click the [Done, Go Back] button and you're all set.
Procedure for performing the zero position calibration for the Steering Angle Sensor (G85) on VW Passat and Audi A4/S4, A6/S6, and A8/S8:
[Select]
[03 - ABS Brakes]
[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
This will store the zero (centered) position of the steering wheel. There should be a displayed message that reads: "Steer. angle sender compens OK". If you get an error, it may mean the Login was not successfully performed.
Click the [Done, Go Back] button and you're all set.

Pero no ha hecho falta. Cuando me dirigia con el coche a un trozo de carretera abandonado a hacerlo, al callejear por el pueblo se ha apagado el chivato. Le he pàsado el Vag-Com y ya no habia ningun fallo.

Gracias Javieres.

[javiersan]

Gracias Javier.
De nada compañero....