reajustar dsg

[Nina]

hola señores pues como dice en el titulo estoy interesado en ressetear mi dsg porque hace alguna cosa que no me gusta si alguien sabe o ha hecho esto con el vag com estaria agradecido que me explicase, he encontrado cosas en ingles pero mi ingles es chungo y no me fio por eso si alguien ya lo ha hecho me haria un favor de explicarmelo




gracias

[serpasoria]

Creo haber leido que cuando hacen cosas raras es por el sensor de temperatura que suelen fallar en las primeras unidades del dsg,y el tuyo parece entra ahi, eso si correjirme si me equivoco.

Salu2.

[cyclope]

Hola:
Vete ha este enlace que se habla de ello.
Saludos
Error al intentar realizar el ajuste basico del DSG ([Only registered and activated users can see links])

[Nina]

Gracias por las respuestas creo rcordar que no me daba ningun error ya volvere a passar el ordeñador

Aun estoy en practicas

[Nina]

Hola otra vez no encuentro en el vag com para hacer el ajuste una ayudita porfa

[ferchir]

6-Speed Direct Shift Gearbox (DSG/02E)

From Ross-Tech Wiki


Jump to: navigation ([Only registered and activated users can see links](DSG/02E)#column-one), search ([Only registered and activated users can see links](DSG/02E)#searchInput)
Contents

[hide ([Only registered and activated users can see links]())]

<LI class=toclevel-1>1 Basic Setting ([Only registered and activated users can see links](DSG/02E)#Basic_Setting)

<LI class=toclevel-2>1.1 Transmission Tolerances (Engaged Calibration) ([Only registered and activated users can see links](DSG/02E)#Transmission_Tolerances_.28Engaged_Calibratio n.29) <LI class=toclevel-2>1.2 Transmission Tolerances (Synch. Point. Measurement) ([Only registered and activated users can see links](DSG/02E)#Transmission_Tolerances_.28Synch._Point._Meas urement.29) <LI class=toclevel-2>1.3 Clutch Adaptation ([Only registered and activated users can see links](DSG/02E)#Clutch_Adaptation) <LI class=toclevel-2>1.4 Reset Values (Clutch Safety Function) ([Only registered and activated users can see links](DSG/02E)#Reset_Values_.28Clutch_Safety_Function.29) <LI class=toclevel-2>1.5 Reset Values (Pressure Adaptation) ([Only registered and activated users can see links](DSG/02E)#Reset_Values_.28Pressure_Adaptation.29) <LI class=toclevel-2>1.6 Reset Values (Steering Wheel Paddle Installation) ([Only registered and activated users can see links](DSG/02E)#Reset_Values_.28Steering_Wheel_Paddle_Install ation.29)
1.7 Reset Values (ESP & Tip Cruise Control Installation) ([Only registered and activated users can see links](DSG/02E)#Reset_Values_.28ESP_.26_Tip_Cruise_Control_In stallation.29)

2 Special Procedures ([Only registered and activated users can see links](DSG/02E)#Special_Procedures)

2.1 Defined Test Drive ([Only registered and activated users can see links](DSG/02E)#Defined_Test_Drive)

2.1.1 Special Notes ([Only registered and activated users can see links](DSG/02E)#Special_Notes)


Basic Setting

Prerequisites:


Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
Selector Lever in P
Ignition ON
Engine ON (Idling)
Brake Pedal operated (hold for the whole procedure)
Throttle Pedal not operated
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
[Select]
[02 - Transmission]


Transmission Tolerances (Engaged Calibration)

Group 061
[Go!]


When you go to Basic Settings 061 and click GO the screen may look like this: Basic Settings 061 ([Only registered and activated users can see links])
Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to [B]On when finished: Basic Settings 061 ([Only registered and activated users can see links])
Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.

Transmission Tolerances (Synch. Point. Measurement)

Group 060
[Go!]


When you go to Basic Settings 060 and click GO the screen may look like this: Basic Settings 060 ([Only registered and activated users can see links])
Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to On when finished: Basic Settings 060 ([Only registered and activated users can see links])
Wait until Basic Settings has switched to ON and all numbers have stopped moving.
Clutch Adaptation

Control Module Software Version < 0800:
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Clutch Safety Function)

Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Pressure Adaptation)

Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Steering Wheel Paddle Installation)

Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (ESP & Tip Cruise Control Installation)

Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

[Done, Go Back]
Switch off Ignition, wait 10 Seconds and switch it back on.
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.




Special Procedures

Defined Test Drive

Suggested test drive after replacing the mechatronic or successful basic setting.

Prerequisites:


Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
Do Not use Cruise Control.
Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.
Evaluate creep and starting-off points.
Check for leaks.

NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.


Special Notes


Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own.


It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.
Retrieved from "[Only registered and activated users can see links](DSG/02E) ([Only registered and activated users can see links](DSG/02E))"

Saludos

[Nina]

si esto ya lo he encontrado pero no me fio de mi ingles por eso si alguien lo ha hecho y me hecha un cable mejor