Fallo abs

[carlostilo]

Mi problema principal es que la pegatina del hueco de la rueda no es legible , pero sé que mis frenos son fn3 , sacados del Elsa ,y el segundo problema es que en la página de rosstech no me viene el la el del Skoda superb , cuando me meto en el coding me aparece una ventana emergente con varios códigos , pero no tiene nada que ver con la de Audi , es totalmente diferente , subo mi scan para que lo veáis

[carlostilo]

VCDS Version: Release 12.12.0
Data version: 20130910

Tuesday,11,June,2019,20:02:05:62939

Chassis Type: 3U (3U - Skoda Superb (2002 > 2008))
Scan: 01 02 03 08 15 16 17 19 36 37 46 47 55 56 76

VIN: TMBCR63U769113985 Mileage: 173640km/107894miles
-------------------------------------------------------------------------------
Address 01: Engine Labels: Redir Fail!
Part No SW: 03G 906 016 GT HW: 028 101 269 8
Component: R4 2,0L EDC G000SG 8203
Revision: 12345678 Serial number: SKZ7Z0E3318398
Coding: 0000072
Shop #: WSC 09456 572 13390
VCID: 7BF511673910BBC6C11-5000

No fault code found.
Readiness: 0 0 1 1 1

-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 3U0-614-517.lbl
Part No: 3U0 614 517 B
Component: ABS/ESP front 1312
Coding: 00000
Shop #: WSC 00000
VCID: 326BFC43FEDABA8E527-5072

2 Faults Found:
01044 - Control Module Incorrectly Coded
35-00 - -
00778 - Steering Angle Sensor (G85)
66-10 - Not Matched - Intermittent

-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 3U0-907-044.lbl
Part No: 3U0 907 044 A
Component: CLIMATRONIC S B5 C 2004
Coding: 17000
Shop #: WSC 00028
VCID: 3169F34FFBDC81962BD-50E6

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags Labels: 6Q0-909-605-VW5.lbl
Part No: 1C0 909 605 F
Component: 0D AIRBAG VW61 0K 0003
Coding: 12356
Shop #: WSC 00028
VCID: 275D1D17C518CF26F59-5000

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments Labels: 3U0-920-xxx-17.lbl
Part No: 3U0 920 811 D
Component: KOMBI+WEGFAHRSP VDO V09
Coding: 31115
Shop #: WSC 00000
VCID: 3169F34FFBDC81962BD-5072
TMBCR63U769113985 SKZ7Z0E3318398

No fault code found.

-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 6N0-909-901-19.lbl
Part No: 6N0 909 901
Component: Gateway K<->CAN 0001
Coding: 00006
Shop #: WSC 00028
VCID: F0EFB64BB056489EE43-5000

No fault code found.

-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 1C0-959-799.lbl
Part No: 1C0 959 799 B
Component: BB Komfortgerát HLO 0004
Coding: 00259
Shop #: WSC 00028
VCID: 3663C05312B2A6AE7EF-4A9C

Subsystem 1 - Part No: 1C1959801
Component: BB Tõrsteuer.FS KLO 0202

Subsystem 2 - Part No: 1C1959802
Component: BB Tõrsteuer.BF KLO 0202

Subsystem 3 - Part No: 3U0959811
Component: BB Tõrsteuer.HL KLO 0202

Subsystem 4 - Part No: 3U0959812
Component: BB Tõrsteuer.HR KLO 0202

No fault code found.

End ---------------------------------------------------------------------

[starwack]

Aqui tienes tu label. En tu autoscan veo que alguien ha cambiado el coding del motor y tu cuadro de instrumentos tambien aparece WSC 0000. Parece que alguien ha cambiado algo en el coche. Prueba a hacer LOGIN antes de meter el CODING. Supongo que en tu vagcom tienes configurado algun numero de WSC, sino es asi no te cogera ningun CODING. Ya contaras como te ha ido.

;
; VCDS Label File
;
; Copyright © 2005-2009 Ross-Tech, LLC
;
; Skoda Superb (3U)
;
; Component: J104 - Brake Electronics (#03) - Bosch 5.7
;
; P/N: 3U0-614-517-???
;
; includes measuring blocks, basic setting, coding and login
;
; created on 09/Dec/2005 by Sebastian Stange (sebastian@ross-tech.com)
;
; last modificationon on 06/Mar/2009
;
; requires VCDS 805.0 or newer
;
;
;---------------------------------------------------
;
; measuring blocks & basic setting
;
;---------------------------------------------------
;
;
001,0,Wheel Speed
001,1,Wheel Speed,Front Left,Display Range: 0.0...255.0 km/h
001,2,Wheel Speed,Front Right,Display Range: 0.0...255.0 km/h
001,3,Wheel Speed,Rear Left,Display Range: 0.0...255.0 km/h
001,4,Wheel Speed,Rear Right,Display Range: 0.0...255.0 km/h
;
B001,0,Steering Angel Sensor (G85) Alignment
B001,1,Steering Angel,Sensor (G85),
B001,2,Alignment, ,
B001,3,Alignment,Status,Specification: OK
B001,4, , ,
;
002,0,Switches && Buttons
002,1,Brake Test Switch,,Display Range: 0/operated
002,2,Brake Light Switch,,Display Range: 0/operated
002,3,Parking Brake,Button,Display Range: 0/operated
002,4,ESP-Passive,Button,Display Range: 0/operated
;
003,0,Engine Data
003,1,Engine Speed
003,2,Engine Torque
003,3,Engine Torque,(loss)
003,4,Throttle Valve Angle
;
004,1,Standing Time
004,2,EDL-T Flag,,Display Range: ON/OFF\nSpecification: OFF
;
005,1,Steering Angle,Sensor (G85),Display Range: -720.0...+720.0 °\nTolerance (when straight): ±5.0 °
005,2,Rotation Rate,,Display Range: -69.0...+69.0 °/s
005,3,Brake Pressure,,Display Range: -41.0...+292.0 bar\n40.0 bar = Short to Ground\n290.0 bar = Short to Plus
005,4,Transverse,Acceleration,Display Range: -25.0...+25.0 m/s²
;
006,1,Supply Voltage,(Terminal 30),Specification: 9.8...17.4 V
006,2,Valve Relay,,Display Range: ON = OK / OFF = not OK
006,3,Return Flow Pump,,Display Range: ON/OFF
006,4,Work Shop Code
;
008,1,Steering Angle,Sensor (G85),Specification: Steer. ang. 1\nDisplay Range: Steer. ang. 0/Steer. ang. 1
008,2,Transmission,,Display Range: Transm. 0/Transm. 1
008,3,Engine,,Specification: Engine 1\nDisplay Range: Engine 0/Engine 1
008,4,Instrument Cluster,,Specification: Instruments 1\nDisplay Range: Instruments 0/Instruments 1
;
125,0,CAN-Databus Communication (Powertrain)
125,1,Steering Angle,Sensor (G85),Specification: Steer. ang. 1\nDisplay Range: Steer. ang. 0/Steer. ang. 1
125,2,Transmission,,Display Range: Transm. 0/Transm. 1
125,3,Engine,,Specification: Engine 1\nDisplay Range: Engine 0/Engine 1
125,4,Instrument Cluster,,Specification: Instruments 1\nDisplay Range: Instruments 0/Instruments 1
;
;
;---------------------------------------------------
;
; login/coding-ii
;
;---------------------------------------------------
;
;
L00,Brake Electronics (J104/Bosch 5.7) Login/Coding-II
L01,09575 = AZM/AWT (Manal Transmission)
L02,09397 = AMX/BBG (Automatic Transmission)
L03,09395 = AMX (Manual Transmission)
L04,09357 = AYM/BDG (Automatic Transmission)
L05,09355 = AYM/BDG/BSS (Manual Transmission)
L06,09555 = AWX/AVB/BSV (Manual Transmission)
L07,09557 = AVF (Automatic Transmission)
L08,09577 = AWT (Automatic Transmission)
L09,
L10,Note: After Login/Coding-II has been carried out you need to recode the Control Module.
L11,
L12,40168 = Basic Settings Enabling (i.e. mandatory prior to Steering Angle Sensor Alignment)
;
;
;---------------------------------------------------
;
; coding
;
;---------------------------------------------------
;
;
C00,Brake Electronics (J104/Bosch 5.7) Coding
C01,04275 = AZM/AWT (Manal Transmission)
C02,04497 = AMX/BBG (Automatic Transmission)
C03,04495 = AMX (Manual Transmission)
C04,04457 = AYM/BDG (Automatic Transmission)
C05,04455 = AYM/BDG/BSS (Manual Transmission)
C06,04255 = AWX/AVB/BSV (Manual Transmission)
C07,04257 = AVF (Automatic Transmission)
C08,04277 = AWT (Automatic Transmission)
C09,
C10,Note #1: Coding is accepted after a specific Login has been carried out.
C11,Note #2: After successful Coding the Steering Angle Sensor Alignment needs to be carried out.
;

[carlostilo]

Mi tipo motor es bss sería primero09355 y después 04455 no ? Si es asin ya lo he probado y no me lo coje

[carlostilo]

Lo de inicio de sesión específico a que se refiere ?

[starwack]

Primero entras en la pestaña de login pones 09555 y luego entras en la pestaña de coding y pones 04255. Revisa tambien el coding que tienes el los instrumentos y en el motor. SI aun asi sigues sin poder meter el coding mira a ver si tienes puesto en tu vagcom WSC (numero de taller, importadora.....)

[carlostilo]

Sigue sin dejarme , cómo miró lo de wsc ?

[starwack]

En la primera pantalla del vacgom entra en options, luego en la pestaña que pone user interface and identification. Ahi pone el WSC importador y numero de equipo.
Suerte

[carlostilo]

De dónde se sacan esos códigos , perdón por la ignorancia

[starwack]

Te los puedes inventar. No hay problema.